Sign In | Join Free | My himfr.com
Home > AC Servo Drive >

Vector Pulse Input AC Servo Motor Driver Internal Planning Position

ShenZhen Vector Technology Co., Ltd.
Contact Now
    Buy cheap Vector Pulse Input AC Servo Motor Driver Internal Planning Position from wholesalers
     
    Buy cheap Vector Pulse Input AC Servo Motor Driver Internal Planning Position from wholesalers
    • Buy cheap Vector Pulse Input AC Servo Motor Driver Internal Planning Position from wholesalers
    • Buy cheap Vector Pulse Input AC Servo Motor Driver Internal Planning Position from wholesalers

    Vector Pulse Input AC Servo Motor Driver Internal Planning Position

    Ask Lasest Price
    Brand Name : Vector
    Model Number : VEC-VC-02733H-M-E
    Certification : CE
    Price : To Be Discussed
    Payment Terms : T/T, Western Union, L/C
    Supply Ability : 500 kits/month
    Delivery Time : 3-5 work days
    • Product Details
    • Company Profile

    Vector Pulse Input AC Servo Motor Driver Internal Planning Position

    Vector Pulse Input AC Servo Motor Driver Internal Planning Position


    Products Description


    Product NameAC Servo Motor Driver
    BrandVector
    Model No.VEC-VC-02733H-M-E
    Power411KW
    Voltage380V
    PhaseThree Phase
    Rated Current27A
    Communication ProtocolsModbus/CANopen/EtherCAT
    Encoder17/23/24 bit absolute encoder

    How is the Servo Drive works? The Location control model, Speed control model and Trogue control model.

    Pulse Command InputPulse TypeDifferential input,Open collector
    Frequency RangeDifferential input:0-500kHz,pulse width greater than 1us
    Open collector: 0-300kHz,pulse width greater than 2.5us
    Pulse Modepulse + direction; AB pluses; CW+CCW;
    Analog InputVoltage Range-10V to 10V
    Input Impedance10kΩ


    Servo Drive Description- Details about a Servo Drive, how to select the Servo drive model and do installation?

    Vector Pulse Input AC Servo Motor Driver Internal Planning Position

    The panel contains 8 buttons and 5 digital tubes. Only 5 of the 8 buttons can be used, and the

    remaining 3 buttons reserved. The general functions of the five buttons are shown in the table below.

    Key NameKey function
    PAR/ALMmode switch, return to the previous menu
    ▲(add)increase flashing bit value of the LED digital tube
    ▼(dec)Decrease flashing digit value of the LED digital tube
    STOP/RSTMoves the blinking LED tube to the left; checks the high value of data
    longer than 5 bits; Fault reset;execute Fn function
    RD/WTread/write parameter values;enter fn page

    Wiring precautions

    ● It is recommended not to use single-phase 220V for main power supply,

    which may cause damage to electrolytic capacitor due to lack of phase.

    ● Do not change the wiring during power-on, otherwise it may cause electric

    shock or injury.

    ● Please perform wiring or inspection by professional technicians, otherwise it

    may cause electric shock or product failure.

    ● Please carefully confirm the wiring and power supply. The output circuit

    may be short-circuited due to wiring errors or application of different voltages. The brake does not operate when the above fault occurs, which may result in mechanical damage or personal injury.

    ● Do not connect the input power cable to the U, V, and W terminals of the

    drive. Otherwise, the servo driver will be damaged.

    ● When wiring, do not pass the power cable and signal cable through the same

    pipe, and do not bundle them together. The distance between the two should be more than 30cm to avoid interference.

    ● The driver ground terminal must be grounded to avoid leakage and reduce

    the interference of the system, and the diameter of the ground wire should be the same as or above the power supply line.

    ● When connecting the AC power supply and DC power supply to the servo unit, connect to the specified terminal. Failure to do so may result in malfunction or fire.

    ● For the wiring length, the command input line is up to 3m and the encoder

    line is up to 20m.

    ● Use a twisted-pair shielded cable for the signal cable and encoder cable, and

    ground the shield with a single end.

    ●The U, V, W terminals of the driver and the U, V, and W terminals of the

    motor should be connected one by one according to the name. If it is wrong connected, the motor cannot operate normally.

    ● Common DC bus products require pressure sensitive resistors and the wiring

    is secure.

    ● Please check the power after the power is off for at least 5 minutes. Even if

    the power is turned off, high voltage may remain inside the servo drive. Therefore, do not touch the power terminal within 5 minutes after the power is turned off, otherwise it may cause electric shock.

    ● Do not turn the power ON/OFF frequently. When it is necessary to

    continuously turn ON/OFF the power, please control it once or less in 1 minute. Since the power supply section of the servo driver has a capacitor, a large charging current (charge time of 0.2 seconds) flows during the ON/OFF power supply. Therefore, if the power is turned ON/OFF frequently, the performance of the main circuit components inside the servo driver will be degraded.

    ● Do not apply power when the terminal block screws are loose or the cable is

    loose. Otherwise, it may cause fire.

    ● Take appropriate shielding measures in the following locations, otherwise

    the machine may be damaged:

    1. Locations that cause interference due to static electricity;

    2. A place that produces a strong electric field or a strong magnetic field;

    3. Locations where there may be radiation radiation;

    4. A place with a power cord nearby.


    Certificates

    1. CE (EU Safety Standard);
    2. IEC/EN61800-5-1:2007 (Safety requirements for electrical, thermal and energy in Section 5-1 of

    the variable speed electric driver system), corresponding to the national standard GB12668.501-2013;

    3, IEC / EN61800-3: 2004 + A1 (speed control electric driver system part 3 electromagnetic compatibility

    standards and its specific test methods), corresponding to the national standard GB12668.3-2012.

    Vector Pulse Input AC Servo Motor Driver Internal Planning Position

    Quality Checking:

    Four times Production testing
    Two Times 24 hoursTesting
    100% Inspection Before Shipping



    Delivery Time and Shipping Way


    1. For small order we always can delivery out within 1 week.

    2. Our products can be shippied via Air, Land or Sea.


    Quantity1-5 kits50-100 kits200-500 kits
    Delivery timeWithin 3 days5-10 days15-25 days

    Packing details of Servo Drive
    ProductsE1(3-6A)E2(7-12A)E3(16-27A)C015(32-38A)C022(45-60A)
    Ctn. Size280*208*78280*208*112375*290*155440*296*288510*305*325

    Exhibition:

    Vector Pulse Input AC Servo Motor Driver Internal Planning PositionVector Pulse Input AC Servo Motor Driver Internal Planning Position


    Quality Vector Pulse Input AC Servo Motor Driver Internal Planning Position for sale
    Inquiry Cart 0
    Send your message to this supplier
     
    *From:
    *To: ShenZhen Vector Technology Co., Ltd.
    *Subject:
    *Message:
    Characters Remaining: (0/3000)