Electric Motors, AC Servo Motor, Servo Drive For Wood CNC Processing Machine

Servo Drive For Wood CNC Processing Machine
AC Power 22KW
Three Phase 380V
Modbus / CanOpen / EtherCAT
Location / Speed / Torque Control Mode
2500 pulse incremental + Hall encoder;

Products Description

Installation Precautions

● Install the driver on a dry and sturdy platform. Maintain good ventilation and

heat dissipation during installation and maintain good grounding.

● Please install in the specified direction to avoid malfunction.

● When installing, please ensure that the servo driver is kept at a specified distance from the inner

surface of the cabinet and other machines, otherwise it may cause fire or malfunction.

Operating precautions

● in the test operation, in order to prevent accidents, please test the servo motor with no load

(not connected to the driver shaft), otherwise it may cause injury.

● when starting to operate on the supporting machine, set the user parameters that match the machine

in advance. If you start operation without parameter setting, it may cause mechanical loss or malfunction.

● to avoid accidents, install a limit switch or a stopper at the end of the movable part of the machine,

otherwise it will cause mechanical damage or injury.

● do not make extreme changes to the parameter settings, as this may result in unstable operation,

mechanical damage or injury.

●when the power is turned on or the power supply is cut off, the heat sink of the servo driver, external

braking resistor, motor, etc. may be in a high temperature state. Do not touch it, otherwise it may cause burns.

● when using a servo motor on the vertical axis, set a safety device to prevent the work piece from falling under

alarm, over travel, etc. In addition, please perform the servo lock stop setting when an over travel occurs,

otherwise the work piece may fall in the over travel condition.

● do not enter the operating range of the machine during operation, otherwise it will cause injury.

● do not touch the servo motor or the movable part of the machine during

operation, otherwise it will cause injury.

● please set up the safety system to ensure safety even in the event of a signal line breakage. For example,

when the positive over travel switch (P-OT) and negative over travel switch (N-OT) signals are disconnected

at the factory setting, they operate safely.

● be sure to set the servo OFF state when turning off the power.

● do not turn the power on/off frequently. After the actual operation starts, the power ON/OFF interval should

be more than 1 hour, otherwise the components inside the servo unit will be prematurely aged.

●when an alarm occurs, reset the alarm after the cause is removed and ensure

safety, and restart the operation, otherwise it may cause injury.

● do not use the brake of the brake motor for normal braking, otherwise it may cause a malfunction.

Accessories:

	Accessory name	Image
Satandard Spare Parts	Power terminal		Adapt to E1,E2 structure drive
	Cn3 encoder plug		Encoder plug on the driver side
	Cn4 control terminal plug		Input/output signal terminals,user wiring
	Encoder connection line		The standard cable length is 3, 5, 8, 10, 13, 15 meters, according to customer needs Provide independent connector
	Power line		The standard cable length is 3, 5, 8, 10, 13, 15 meters, according to customer needs Provide independent connector
	Drive monitoring line		Connect and adjust the software for remote monitoring and firmware update
Purchasing Spare Parts	USB to RS232 Adapter cable		If necessary, self purchase
	Ethernet communication line		If necessary, self purchase

Certificates
1. CE (EU Safety Standard);
2. IEC/EN61800-5-1:2007 (Safety requirements for electrical, thermal and energy in Section 5-1 of the
variable speed electric driver system), corresponding to the national standard GB12668.501-2013;
3, IEC / EN61800-3: 2004 + A1 (speed control electric driver system part 3 electromagnetic compatibility
standards and its specific test methods), corresponding to the national standard GB12668.3-2012.

Quality Checking:
Four times Production testing
Two Times 24 hoursTesting
100% Inspection Before Shipping

Delivery Time and Shipping Way

1. For small order we always can delivery out within 1 week.
2. Our products can be shippied via Air, Land or Sea.

Packing:

Our Team:

Focusing on industrial automation products with independent intellectual property rights, we are positioned to serve high end equipment manufacturers and provide overall solutions for customers in market segments. To become the world's leading provider of industrial automation products and solutions. Independently developed products include servo drive, motion controller, human-machine interface, servo motor, etc., with a number of invention patents, utility model patents and software registration rights, is a national high-tech enterprise. Has its own product research and development center and production base, in the country has a number of offices and agents. Our core competitiveness is to achieve seamless integration of product R&D and product application, and provide professional and efficient system solutions for equipment.

Vector will continue to adhere to the business philosophy of “creating value for customers wholeheartedly”make deep efforts in the field of industrial automation, and create the beauty of motion control is our unremitting pursuit, determined to build a national brand with leading technology, efficient management, leading domestic and internationally renowned.